Humidity Levels

HEPHumidity Levels

Humidity Levels | Dehumidifier Installation | Heating and Air Conditioning | Palmer

In Palmer’s moody climate, excess indoor moisture can leave your home feeling muggy, trigger mold growth, and overwork your air conditioner. HEP’s Humidity Levels Heating and Air Conditioning team brings quick relief with professional dehumidifier installation, tailoring each system to your square footage and existing HVAC equipment. Our factory-trained technicians measure, size, and route drainage correctly, so you get crisp, balanced air without the hassle of portable units or constant bucket emptying.

From the moment we arrive, we treat your home like our own—laying down protective coverings, keeping tools organized, and testing every setting before we leave. The result is healthier air, lower utility bills, and a longer life for your cooling system. Schedule your free in-home assessment today and discover why Palmer homeowners trust HEP to keep comfort in perfect balance.

FAQs

Why is controlling indoor humidity so important for homes in Palmer?

Palmer experiences warm, often wet summers and long, cold winters, both of which can push indoor relative humidity outside the recommended 30–50 percent range. Excess moisture fosters mold, mildew, dust mites, and wood rot, while air that is too dry can aggravate allergies, dry out skin, and damage hardwood floors and musical instruments. Installing a whole-home dehumidifier keeps humidity in the ideal zone year-round, improving comfort, protecting your home’s structure and furnishings, and even helping your HVAC system run more efficiently.

How does a whole-home dehumidifier integrate with my existing heating and air-conditioning system?

A whole-home dehumidifier is plumbed directly into your HVAC ductwork—usually at the return plenum—so it treats all the air that circulates through your furnace or air handler. When indoor humidity rises above the set point, the dehumidifier draws moist air through its coil, condenses and drains the water, then sends dry, conditioned air back into the supply duct. The unit is wired to your HVAC control board or its own dedicated humidity controller, allowing fully automatic operation that works in tandem with your thermostat.

What size dehumidifier will my Palmer home need?

Sizing is based on square footage, ceiling height, typical moisture load (basements, crawlspaces, number of occupants, cooking and shower frequency), and desired humidity set point. Most single-family homes in the Palmer area require units rated between 60 and 120 pints per day. During your free in-home assessment, our comfort consultant measures current humidity, inspects problem areas, and calculates load requirements to recommend the right capacity so you don’t under- or over-size the equipment.

Will running a dehumidifier increase my energy bills?

A dehumidifier does use additional electricity, but many homeowners see little or no net increase—and sometimes a decrease—in total energy costs. That’s because drier air feels cooler in summer and warmer in winter, allowing you to raise the thermostat a few degrees without sacrificing comfort. Removing moisture also reduces the latent load on your air conditioner, so it cycles less and runs more efficiently. High-efficiency models we install draw as little as 4–6 amps and are ENERGY STAR® certified.

How much maintenance does a whole-home dehumidifier require?

Very little. Every 3–6 months you or your HVAC technician should: (1) replace or rinse the air filter, (2) inspect and clean the coil if dust accumulates, and (3) verify the condensate drain and pump (if used) are clear. During your annual heating or cooling tune-up, we’ll also check electrical connections, the humidistat calibration, and overall system operation. With routine care, modern units typically last 8–15 years.

What is the installation process and how long will it take?

After the in-home evaluation and equipment selection, installation is usually completed in one visit lasting 4–6 hours. Our certified technicians: • isolate power to your HVAC system, • cut an access port and mount the dehumidifier on a vibration-isolating platform or hanging kit, • connect supply and return ductwork with insulated flex or hard pipe, • pipe the condensate line to an existing floor drain or condensate pump, • wire the unit to the control board or wall-mounted humidistat, • program humidity set points, and • test-run the system to confirm proper airflow, drainage, and leak-free operation. We leave the work area clean and provide a brief orientation on operating your new equipment.

HEP
Book Online
(423) 819-7773